craftsman 2800 psi pressure washer outdoor bleach

CRAFTSMAN 2800 PSI PRESSURE WASHER OUTDOOR BLEACH HOW TO

What To Do If Pressure Washer Soap Won’t Dispense Point the wand at the surface you intend to clean and spray the soap from the bottom upward.Press the toggle switch to the ‘on’ position to turn the power washer on.Turn the water faucet clockwise to turn the water flow on.Pull the quick connect hose nozzle backward and push a garden hose into the opening, then the quick connecter to fasten the hose.This puts the setting on low-pressure mode for dispensing soap. Holding the pressure washer nozzle in one hand, push the nozzle forward with the other.Push the small end of the filter siphon tube into the detergent container, so it touches the bottom.Failure to properly dilute the soap will cause clogs. Mix the soap solution following the product instructions.There are few things as satisfying as watching a concrete driveway come clean! Follow these steps to get spraying: Now that you’ve got your unit running, it’s time to give it a try. Ensure the new spark plug is of the correct specification for your Craftsman power washer model. If it’s damaged or has been in use for a long time, consider replacing it with a new one. If it appears dirty or corroded, clean it with a wire brush.

Check the spark plug for any signs of wear or damage. A damaged or fouled spark plug can prevent the power washer from starting. Use carburetor cleaner to spray and clean the component, then allow it to dry before attempting to start the washer.Ī third potential issue is a faulty spark plug. Ensure the power washer is off and the spark plug is disconnected. To resolve this, the carburetor may need cleaning. Over time, residue can build up in the carburetor, preventing the proper mixture of air and fuel. Drain the old fuel, replace it with fresh gasoline, and try starting the power washer again.Īnother common reason a Craftsman power washer might not start is a clogged carburetor. Gasoline left in the washer for extended periods can degrade and prevent the engine from starting. If your Craftsman power washer won’t start, it might be due to old or contaminated fuel. What to Do if Your Craftsman Power Washer Won’t Start If you are having issues, you can begin to troubleshoot it with the techniques listed in the next section. If followed correctly, your power washer should start right up.

Move the engine choke to the ‘run’ position once the engine warms up.

Grab the rubber handle attached to the pull-string on top of the engine firmly and continue to do so until there is light resistance.

If the engine is cold, put it in the “choke” position.

If the engine is hot, put the choke in the “run” position.

Push the throttle lever (this is located on the right side of the engine), to its “Fast” setting.

This locks the trigger in the off position.

Pull the trigger lock (the small spring-loaded tab located on the bottom of the trigger) downward.

Slide the nozzle extension to its low-pressure position.

Screw the nozzle extension (just hand-tight) to the end of the spray gun.

Continue pressing until water begins to flow freely.

Press and hold the trigger on the sprayer gun to clear any air or debris.

Turn the water supply on, starting the flow of water into your washer.

Using your hand, attach the hose tightly to the pressure by way of the water inlet., which is clearly labeled.

Check the high-pressure hose connecting the water pump and the spray handle with a combination wrench to make sure it is tightened correctly.

Attach one end of a common garden hose to your outside water supply.

Make sure your power washer is on a flat surface.

Below is a step by step guide to starting your power washer. There are certain steps you need to take each time you start your power washer due to the gas-powered engine. Keep in mind that if these issues can’t be easily fixed at home, the warranty only requires you to bring it to an authorized service center for more help.

CRAFTSMAN 2800 PSI PRESSURE WASHER OUTDOOR BLEACH HOW TO

We’ve put together a simple to understand comprehensive guide of the most common issues and how to fix them. How to effectively stop your power washer.How to pressurize your power washer correctly.What to do when the soap won’t dispense.What do if your power washer won’t start.Within this guide, you’ll find solutions to the following common issues: Your equipment is backed by a three-year limited frame warranty and a two-year limited engine warranty, but many issues require just a little troubleshooting, followed by an easy fix. The reliable Briggs & Stratton engine makes everyday home cleaning tasks easy. When you purchase a Craftsman power washer, you can rest easy knowing you have a quality piece of equipment you can depend on.

Craftsman 2800 psi pressure washer outdoor bleach